HomeAbout
PortfolioBlogCareersContact Us
Illustration of injection molding terms: mold halves, gate and runner, ejection, cooling time and part inspection

Injection Molding Glossary: 23 Terms Explained

Gates, runners, shrinkage, cycle time, common defects and the terms that drive cost, explained in plain language.

Injection molding has its own vocabulary, and it gets used in every drawing review, quotation and trial report. This glossary explains the 23 terms you will hear most often, what each one means on the shop floor, and why it matters for the quality and cost of your part.

If you are budgeting a project, our cost guide and cost reduction guide build on these terms.

1. Mold Design Terms

Gate

The opening through which molten plastic enters the mold cavity.

Why it matters: Gate size and position decide how the cavity fills, where weld lines form and where a small mark is left on the part. A badly placed gate causes flow marks, air traps and weak weld lines.

Runner

The channel that carries molten plastic from the sprue to each gate.

Why it matters: Runner layout affects material waste, cycle time and how evenly the cavities of a multi-cavity mold fill.

Draft Angle

A slight taper on surfaces that run in the direction the mold opens, so the part releases cleanly.

Why it matters: Too little draft makes parts stick, drag or scratch on ejection and wears the mold. Typical draft is 0.5° to 2°, more on textured surfaces.

Parting Line

The line on the part where the two halves of the mold meet.

Why it matters: It leaves a faint witness line and, if the mold halves do not seal well, flash. Its position is agreed early so it stays off cosmetic faces.

Sprue

The main channel that takes molten plastic from the machine nozzle into the runner system.

Why it matters: It is the first part of the flow path, so its size affects the pressure needed to fill the mold.

2. Material and Flow Terms

Shrinkage

The reduction in size as plastic cools and solidifies in the mold.

Why it matters: The mold is cut oversize to allow for it. Every material shrinks by a different amount; PP shrinks much more than ABS, for example, so switching material after the tool is made can put parts out of tolerance.

Warpage

Distortion of a part caused by uneven shrinkage as it cools.

Why it matters: Warped parts do not fit their assembly. Common causes are uneven wall thickness, unbalanced cooling and a poorly placed gate.

Weld Line

The line where two flow fronts of molten plastic meet inside the cavity.

Why it matters: It can be visible and is weaker than the surrounding material. Gate position and flow simulation are used to move weld lines away from load-bearing or cosmetic areas.

Flow Length

The distance plastic travels from the gate to the furthest point of the cavity.

Why it matters: Long, thin flow paths may not fill completely, which decides how many gates a part needs and where they go.

3. Process Terms

Cycle Time

The total time to mold one shot: filling, holding, cooling, mold opening and ejection.

Why it matters: Machine time is paid for by the second, so cycle time is one of the biggest drivers of part cost. Taking 2 seconds off a 20-second cycle gives 10% more parts from the same machine.

Holding Pressure

Pressure kept on the melt after the cavity fills, pushing in extra material as it shrinks. Also called packing pressure.

Why it matters: It prevents sink marks and keeps part weight and dimensions consistent from shot to shot.

Cooling Time

The time the part stays in the closed mold until it is solid enough to eject.

Why it matters: Cooling is usually the largest share of the cycle, often 60% to 70%, which is why cooling-channel design matters so much for cost.

Injection Pressure

The pressure used to push molten plastic into the cavity.

Why it matters: Too little causes short shots; too much causes flash and locked-in stress in the part.

Venting

Small gaps in the mold that let trapped air escape as the cavity fills.

Why it matters: Poor venting causes burn marks and incomplete filling, usually at the last point to fill.

Clamping Force

The force the machine uses to hold the mold closed against injection pressure, measured in tonnes.

Why it matters: Too little and the mold opens slightly, causing flash. It decides which machine size a job needs.

4. Common Defects

Flash

A thin fin of excess plastic at the parting line or around ejector pins.

Why it matters: It has to be trimmed off. Causes include excessive injection pressure, low clamping force and worn mold surfaces.

Sink Marks

Small depressions on the surface, usually opposite thick sections such as ribs and bosses.

Why it matters: They come from thick walls, too little holding pressure or too short a cooling time, and are best prevented at the design stage.

Short Shot

A part that is incomplete because the cavity did not fill.

Why it matters: Causes include low injection pressure or speed, blocked gates, poor venting and flow paths that are too long or thin.

Burn Marks

Brown or black marks where trapped air overheated as it was compressed.

Why it matters: Usually fixed by improving venting or reducing injection speed at the end of fill.

5. Terms That Affect Cost

Multi-Cavity Mold

A mold that produces several identical parts per shot, such as 2, 4 or 8 cavities.

Why it matters: It costs more to build, but for high volumes it cuts the cost per part sharply because each machine cycle makes several parts.

Hot Runner

A heated runner system that keeps the plastic molten inside the mold, so no runner is ejected with the part.

Why it matters: It raises mold cost but removes runner waste and often shortens the cycle, which pays back on long production runs.

Cold Runner

A conventional runner that solidifies each cycle and is separated from the parts.

Why it matters: Cheaper to build and simpler to maintain; well suited to lower volumes. The runner can often be reground and reused.

Regrind

Runners, sprues or rejected parts ground back into granules and mixed with new material.

Why it matters: It lowers material cost, but too much can weaken parts or change their colour, so the allowed percentage depends on the application.

How the Terms Connect

None of these works on its own. In a real project they pull on each other:

What Goes Wrong When They Are Ignored

All of these are caught in a DFM review before the mold is built, which is why every Prismatech project starts with one. In the smart meter casing we produce for a client, now past 100,000 units, it is steady control of cycle and cooling that keeps every batch the same.

Frequently Asked Questions

What is cycle time in injection molding?

The total time to mold one shot, including filling, cooling and ejection. Because machine time is charged by the second, a shorter cycle directly lowers the part price.

What is a gate?

The opening where molten plastic enters the cavity. Its position affects how the part fills, where weld lines form and where a small mark is left.

What causes warpage?

Uneven shrinkage as the part cools, usually from uneven wall thickness, unbalanced cooling or a poorly placed gate.

What is the difference between a hot runner and a cold runner?

A hot runner keeps the plastic molten so no runner is ejected; it costs more to build but saves material and cycle time on long runs. A cold runner solidifies each cycle and is cheaper to build, which suits lower volumes.

Have a project in mind?

Share your drawing for a quick cost estimate and DFM review. We respond within a business day.