The material decides more about a molded part than almost anything else: how strong it is, how it copes with heat and sunlight, how it looks, how accurately it can be held to size, and what it costs. Getting the material right at the start saves tool changes and requalification later.
This guide covers the nine plastics we mold at Prismatech: what each one is good at, where it falls short, and the kind of parts it usually ends up in. If you would rather answer a few questions and get a shortlist, try our Material Selection Tool.
How to Choose a Plastic
Choosing the Right Plastic
What is your primary requirement?
There is no single best plastic. The right one is the cheapest material that reliably does the job, and working that out means answering a handful of questions about the part:
- What does the part do? A housing, a gear, a bracket and a food container each need different properties.
- Where will it live? Heat, sunlight, moisture, oils and cleaning chemicals all rule some materials out.
- What rules apply? Food contact, flame retardancy or electrical insulation requirements narrow the list to specific certified grades.
- How should it look? Gloss, texture, colour matching and clear parts favour some materials over others.
- How accurate must it be? Shrinkage and moisture absorption differ a lot between plastics, and that affects achievable tolerances.
- What can it cost? Material price, cycle time and scrap rate together set the part price, not the resin price alone.
Plastics We Mold
Grades within each family vary widely (filled, flame-retardant, UV-stabilised, food-contact), so treat the notes below as a starting point. We confirm the exact grade with you during DFM review.
Polypropylene (PP)
The workhorse of high-volume molding. PP is light, cheap, resists most chemicals and handles repeated flexing well, which is why it is used for living hinges on caps and lids. Food-contact grades are widely available.
Typical parts: Caps and closures, containers, household and FMCG parts, living-hinge lids, trays.
Watch out for: Low stiffness and heat resistance, brittleness in the cold (homopolymer grades), relatively high shrinkage, and poor adhesion for paint and glue. Outdoor parts need a UV-stabilised grade.
High-Density Polyethylene (HDPE)
Tough, chemically resistant and unbothered by water, with good impact strength even at low temperatures. Like PP, it is inexpensive and available in food-contact grades.
Typical parts: Crates, bins, containers, caps, handles, water and chemical handling parts.
Watch out for: Low stiffness, a soft waxy surface, and high shrinkage that makes tight tolerances difficult.
High-Impact Polystyrene (HIPS)
A low-cost, easy-to-mold plastic with good dimensional stability and a surface that takes printing and painting well. It is a common choice for parts that need to look tidy but live an easy life.
Typical parts: Consumer product housings, trays, appliance internals, display parts, toys.
Watch out for: Weak resistance to heat, sunlight and many chemicals, and lower toughness than ABS.
ABS
The default choice for housings. ABS balances toughness, stiffness and a high-quality surface finish, holds its shape well, and can be painted, printed or textured. Flame-retardant grades are available for electrical products.
Typical parts: Electrical and electronic enclosures, appliance housings, covers, automotive interior trims, toys.
Watch out for: Yellowing and embrittlement outdoors unless UV-stabilised, moderate heat resistance, and poor resistance to some solvents.
Polycarbonate (PC)
Exceptionally tough and naturally transparent, with good heat resistance and dimensional stability. PC is the go-to material when a part must be clear and survive impacts, and flame-retardant grades are common in electrical work.
Typical parts: Meter covers and windows, lenses and light covers, safety and protective parts, electrical enclosures.
Watch out for: Stress cracking when exposed to certain chemicals, sensitivity to sharp notches, a surface that scratches, and the need for thorough drying before molding. It also costs more than ABS.
PC-ABS Blend
A blend that combines much of the toughness and heat resistance of PC with the easier processing and finish of ABS. It suits housings that need to be thinner or tougher than plain ABS allows.
Typical parts: Electronic and meter enclosures, charger and adaptor housings, automotive interior parts.
Watch out for: Higher cost than ABS and only moderate chemical resistance.
Nylon (PA6 / PA66), including Glass-Filled
Strong, tough and wear resistant, with good resistance to oils and fuels. Adding glass fibre (for example PA66 GF30) greatly increases stiffness and heat resistance, making glass-filled nylon a common replacement for metal in brackets and structural parts.
Typical parts: Gears, clips, fasteners, brackets, cable ties, connector bodies, automotive parts near heat.
Watch out for: Moisture absorption, which changes both size and stiffness and must be allowed for in tolerances; thorough drying before molding; and with glass-filled grades, visible fibres on the surface and warpage that depends on flow direction.
PBT (including Glass-Filled)
A polyester with very low moisture absorption, so parts stay the same size in humid conditions. PBT insulates well, resists heat (especially glass-filled) and is widely used in flame-retardant grades for electrical parts.
Typical parts: Connectors, terminal blocks, relay and switch parts, sensor housings, automotive electrical parts.
Watch out for: Sensitivity to sharp notches, gradual degradation in prolonged hot water, and warpage with glass-filled grades.
Acetal (POM)
Stiff, slippery and hard wearing, with excellent dimensional stability and fatigue resistance. POM is the classic material for small precision moving parts that rub against each other.
Typical parts: Gears, bushings, rollers, snap-fits, clips, valve and pump parts.
Watch out for: Poor UV resistance, attack by strong acids, difficulty bonding or painting, and high shrinkage that must be designed for.
Quick Comparison
Relative ratings for typical unfilled grades unless stated. Specific grades can differ considerably, so use this to narrow the options, not to make the final call.
| Material | Heat | Impact | Stiffness | Cost | Typical parts |
|---|---|---|---|---|---|
| PP | Low to Medium | Medium | Low | Low | Caps, containers, hinges |
| HDPE | Low | High | Low | Low | Crates, bins, containers |
| HIPS | Low | Medium | Medium | Low | Trays, consumer housings |
| ABS | Medium | Medium to High | Medium | Medium | Housings, enclosures |
| PC | High | Very high | Medium | High | Clear covers, meter windows |
| PC-ABS | Medium to High | High | Medium | Medium to High | Electronic enclosures |
| PA6 / PA66 | High | High | Medium | Medium | Gears, clips, fasteners |
| PA66 GF | Very high | Medium | Very high | Medium to High | Brackets, structural parts |
| PBT | High | Medium | Medium to High | Medium to High | Connectors, terminal blocks |
| POM | Medium to High | Medium | High | Medium | Gears, bushings, snap-fits |
Material Choice Starts at the Drawing
Material and design are decided together. Wall thickness, rib and boss proportions, draft angles, gate position and even the tolerances on the drawing all depend on how a particular plastic flows, shrinks and cools. Switching material after the tool is built often means changing the tool too.
That is why material selection is part of every DFM review we carry out. We look at the part's job and environment, suggest the grades worth considering, and point out any design changes the chosen material needs before steel is cut.
Frequently Asked Questions
Which plastic is used most in injection molding?
Polypropylene and ABS are among the most widely molded plastics. PP dominates cost-sensitive, high-volume parts such as caps and containers, while ABS is the usual starting point for housings and enclosures.
Which plastic is best for electrical enclosures?
ABS, PC and PC-ABS are the most common choices, usually in flame-retardant grades where the product standard requires it. PC is used when the enclosure needs a clear window. For connectors and terminal parts, PBT and glass-filled nylon are more typical.
Which plastics are suitable for food contact?
Food-contact grades exist for PP, HDPE, PC, POM and several others. Suitability depends on the specific grade and its certification from the resin supplier, not on the material family, so the grade is confirmed and documented before production.
Do you mold glass-filled materials?
Yes. We mold glass-filled nylon and PBT. Glass fibre raises stiffness and heat resistance, but it also increases tool wear and can cause direction-dependent warpage, so gate position and wall design are reviewed carefully at the DFM stage.
Can molded parts be made in custom colours?
Most of these materials can be coloured using masterbatch or pre-coloured compound. Share your colour reference or sample and we will advise what is achievable for your material and finish.
Can you help us choose the material?
Yes. Material selection is part of our DFM review. You can also use the Material Selection Tool for a quick shortlist, then share your drawing with us to confirm the right grade.
Not Sure Which Material Fits Your Part?
Share your drawing and a short description of what the part does and where it is used. Our team will suggest suitable materials and send a quotation.

