The cheapest way to lower the price of a molded part is rarely a cheaper supplier. Most of the cost is fixed long before production, by the part design, the mold and the process. Changes at that stage cost little and keep paying back for the whole life of the program.
This guide covers where part cost comes from and the practical steps that bring it down without hurting quality.
1. Where Part Cost Comes From
| Cost driver | Impact | Where to act |
|---|---|---|
| Cycle time | Very high | Wall thickness, cooling design |
| Tooling | Very high | Number of cavities, runner system |
| Material | High | Grade selection, part weight |
| Rejects and scrap | Medium to high | DFM, process control |
| Secondary operations | Medium | Design for assembly, automation |
Material price gets most of the attention, but over a long run cycle time and tooling usually matter more. Our cost guide shows how these add up for a real part.
2. Design Changes
Decisions made on the drawing have the biggest effect on cost, and they are the cheapest to change.
Reduce wall thickness
Thicker walls use more material and take longer to cool. Bringing walls down to the minimum that still meets strength requirements cuts both material and cycle time. On a high-volume part, even 0.2 mm less wall can save a meaningful amount every year.
Keep walls uniform
Uneven walls cool unevenly, which causes warpage and sink marks and forces a longer cycle. Uniform walls improve quality and speed at the same time.
Add enough draft
Without draft, parts stick, scratch and wear the mold. Allow 0.5° to 2° depending on the material and surface texture.
Do not over-engineer
Extra ribs and bosses, and tight tolerances on dimensions that do not need them, all add tool complexity, cycle time and inspection. Put tight tolerances only on the dimensions that really matter.
A DFM review before tooling catches all of these while they are still easy to fix.
3. Tooling Choices
The mold is paid for once, but it sets the cost of every part it makes.
Single- or multi-cavity
A multi-cavity mold costs more to build but makes several parts per cycle, so for high volumes it lowers the cost per part considerably. The tool cost vs part cost example shows how the mold cost spreads over volume.
Hot runner or cold runner
| Hot runner | Cold runner | |
|---|---|---|
| Mold cost | Higher | Lower |
| Runner waste | None | Some, unless reground |
| Cycle time | Usually shorter | Usually longer |
| Best for | High volumes, long runs | Lower volumes, shorter runs |
For long production programs, a hot runner often lowers the total cost despite the higher mold price.
4. Process Improvements
Shorten the cycle
Seconds add up. On a machine running around the clock, taking a 20-second cycle down to 18 seconds produces about 14,400 extra shots a month from the same machine:
| Cycle time | Shots per hour | Shots per month (24/7) |
|---|---|---|
| 20 s | 180 | about 1,29,600 |
| 18 s | 200 | about 1,44,000 |
More parts per machine hour means a lower cost per part and faster delivery.
Improve cooling
Cooling is usually 60% to 70% of the cycle, so better cooling channels are often the single most effective process improvement.
Automate handling
Automatic ejection, conveyors and robots reduce labour, handling damage and variation between shots, which helps most on high-volume runs.
5. Material Selection
An over-specified material is one of the most common hidden costs. Choosing the least demanding grade that meets every requirement can cut material cost substantially.
- Use ABS instead of PC where the impact and heat requirements allow; it is easier to process.
- Use a glass-filled grade where the extra stiffness lets you thin the walls.
- Allow regrind where the application permits, to reuse runners and rejects.
Any change must still meet the part's mechanical, environmental and regulatory requirements. Our plastic materials guide compares the options.
6. Mistakes That Raise Cost
- Choosing a supplier on price alone: Low quotes often come with more rejects and less consistent quality.
- Skipping DFM: Small design changes before tooling save more than any negotiation afterwards.
- Underinvesting in the mold: A poorly built tool causes problems for its whole life.
- Tight tolerances everywhere: They raise tooling cost, cycle time and inspection effort.
- No technical discussion at RFQ: Comparing prices without comparing approaches leads to the wrong choice.
Quick Checklist
- Walls as thin as strength allows, and uniform
- Draft of 0.5° to 2° on every surface
- Tight tolerances only on critical dimensions
- Multi-cavity tooling for volumes above about 1 lakh parts a year
- A hot runner considered for long production runs
- Cooling design reviewed to shorten the cycle
- Material matched to the real requirement
- A DFM review before the mold is built
Frequently Asked Questions
What is the biggest cost driver in injection molding?
For high-volume parts it is usually cycle time and tooling rather than material. Taking 2 seconds off a 20-second cycle gives 10% more parts from the same machine.
Does a multi-cavity mold reduce part cost?
Yes, for high volumes. The mold costs more, but each cycle makes several parts, so the cost per part falls.
Should I choose the cheapest supplier?
Not on price alone. A low quote can mean more rejects, inconsistent quality and delays. Compare engineering capability and process control as well as price.

