HomeAbout
PortfolioBlogCareersContact Us
Illustration of a DFM review: draft, wall thickness, gate position, ribs and undercuts checked on a molded part

Solve Problems Before Tooling Begins.

Our engineering-led DFM review identifies design, material, tooling and cost issues before they become expensive production problems.

A DFM review is an engineering check of your part design before any tool steel is cut. It answers three questions: will the part mold reliably, will it hold the dimensions you need, and can it be made at a sensible cost at your volumes. Changes are cheap on the screen and expensive once the mold exists, so this is where we solve problems.

Every Prismatech project starts with one. Because we design and build the mold in our own toolroom, the review feeds straight into the tool design rather than being handed to a third party.

What the Review Covers

From Our DFM Reports

Every review is delivered as a slide-by-slide report, each point marked OK, NG or needing the customer's decision. These pages are taken from recent reports on customer parts.

Prismatech DFM report: Part details
Part details. Size, projected area, wall thickness and weight are recorded, and the clamp force and machine tonnage are worked out before anything else.
Prismatech DFM report: Parting line
Parting line. Cavity and core sides are defined and the parting line is marked so any visible witness line is agreed up front.
Prismatech DFM report: Draft analysis
Draft analysis. A- and B-surfaces are checked against the pull direction; here the review calls for 0.5 degrees on a surface that had none.
Prismatech DFM report: Gate position
Gate position. The preferred gate type and location are proposed, and the resulting visible mark is shown so the customer can accept or move it.
Prismatech DFM report: Fill analysis
Fill analysis. Flow simulation shows the fill sequence and the last-fill area, where air traps and weld lines would form.
Prismatech DFM report: Ejection
Ejection. Ejector positions are proposed on the B-surface, avoiding cosmetic faces and thin sections.
Prismatech DFM report: Design suggestion
Design suggestion. A radius that would have created an undercut in the tool is flagged, with a suggested change that molds cleanly.
Prismatech DFM report: Weld lines and air traps
Weld lines and air traps. Where a customer-preferred gate would leave weld lines and air traps on a locking feature, the review shows it and proposes an alternative.

Flow Simulation for Demanding Parts

For complex or tight-tolerance parts we add mold-flow simulation before finalising the tool design. It shows how the cavity fills, where pressure and weld lines land, and how shrinkage is distributed, so gate position, wall transitions, packing and cooling can be adjusted while they are still drawings. Straightforward parts do not need it; the standard review covers them.

How It Works

For most projects an initial DFM assessment comes with the quotation, so cost drivers and tooling complexity are visible before you commit. The full report follows on order. If your tooling is being made elsewhere, we can provide DFM as a separate engagement.

Why It Pays

Most production problems in molded parts are decided at the design stage. A design that ignores draft, wall thickness or gate position leads to a mold that needs rework, longer cycle times and inconsistent parts for the whole life of the program. An hour of review at the start saves weeks of trial-and-correction later. The 12-part smart meter casing we built for a client, now past 100,000 units, went through exactly this process before its tool was built.

Frequently Asked Questions

When should DFM be done?

Once the part design is reasonably settled but before tooling starts. The earlier the better: issues found now cost almost nothing to fix; found at first trial they cost weeks.

What files do you need?

A STEP file is best because it preserves the geometry exactly. IGES, PDF and DWG are accepted but may need clarification. Add the material, volume and critical dimensions if you know them.

Can you hold tight tolerances?

Yes, where the geometry and material allow it. Tell us which dimensions are critical; we confirm what is achievable during the review, design the tool and process around them, and validate them at sampling.

Is there a charge?

DFM review is included in our tooling package. For standalone reviews, where the mold is being built elsewhere, we quote it separately.

Ready for a DFM Review?

Send your drawing or 3D model and our engineering team will come back with the review and a quotation.

Have a project in mind?

Share your drawing for a quick cost estimate and DFM review. We respond within a business day.